EC & IG Series: Offline Data Storage Path
IG: /var/user/data/offline data EC： /userdata/.ieos/device supervisor/data/dbhome/device_supervisor/offlinedata/default1
IR302 Continuously Disconnecting and Reconnecting
Hello, I recently purchased an Inhand IR302 to provide a cellular connection to a computer via ethernet. I have a SIM card that I put in the IR302. When I configure it for AT&T it says “detecting modem” and after a few seconds it connects. However, after
How to edit the meauring points configs of IG101 remotely?
1. Configure the points table on local Config tool, and export the points table. 2. On DM, click the Add config under Edge Computing-->Edge Application-->IG101_MODBUS_APP to upload the point table file, then give a Config Version, the format is v1.0.0
How to deploy config to IG101 remotely?
1. Login your own account on Device Manager, make sure that the device is online on the cloud. Click export button to export the .cfg file. 2. Open the Config Tool locally on your PC, then import the .cfg file downloaded. 3. Change the configurations
Dial Switch on IG502
The pull-down resistance is OFF by default, and the dial switch is close to the non-antenna side. The corresponding relationship of dial switch is as follows: Interface 1A pull-up resistance Interface 1B pull-down resistance Interface 2A pull-up resistance
How to set router to connect to another WiFi(WAN-STA)
This gudie is avaliable for IR302, IR305, IR315, IR615. 1. Connect PC to router via Ethernet, open web browser and go to 192.168.2.1 (if this doesn't work, try incognito mode with http://192.168.2.1). Log in with default username and password on the back
How to perform a Factory Reset on IR302
There are two ways to perform the factory reset on IR302: Software way: Navigate to the System-->Config Management, Click the Restore default configuration 2.Hardware way: a: Power on the device and immediately press and hold the RESET botton until the
HTTP API Document for IR300 and IR600 series
Regarding IR series, we provide the HTTP_API for parameters value checking and setting. Please check the attachment for your reference. The document IR600 and IR300 HTTP API and Status Report-1.9 is the total info of the HTTP_API, contains how to set
How to Set System Log on IR Series?
Please check the attached guide, which shows detailed steps for how to set system log on IR series.
How to install the SIM card of InRouter305 correctly?
InRouter305 uses pop-up card holder. Stab the hollow at the left of the card holder and the card holder will pop up. Then, install the SIM/UIM card and press the card holder back to the card slot. To prevent damage to the SIM card, please power off the
How to adjust the login timeout of IR302?
pls follow the below steps
How to remotely restart a device through a web interface?
pls follow the below steps 1. login the web gui 2.[System → Reboot], click the "Rboot" button. During the restart process, the network will be temporarily interrupted. It is recommended to avoid operating during peak business hours.
How to check the signal indicator light of IR900 router?
If all three indicator lights are on, it means the signal is good (20-31asu). If two lights are on, it means it is basically normal. If only one light is on, the antenna or SIM card needs to be checked.
Does the SIM card support hot swapping?
No, the SIM card must be inserted while the device is powered off, pressed until the card slot is locked, and the device will automatically recognize it when powered on.
What is the default login account password for Inhand devices?
The default account for the previous device was adm and the password was 123456. It is recommended to change it immediately for the first login to ensure security. In order to meet security requirements, the main focus now is on the initialization password
Use Case: Secure Networking for Smart ATMs & Financial Kiosks
1. Scenario A commercial bank plans to deploy a fleet of new "Smart ATMs" and self-service financial kiosks in shopping malls and convenience stores. Challenges: Security: Financial transaction data requires the highest level of encryption and protection
IR routers band locking
At present, the locked frequency band can only be filled in through AT initialization command Format: AT+QCFG="band",<bandval>,<Itebandval> <bandval>: Configure GSM/WCDMA frequency bands. 0: Do not change the existing configuration. <Itebandval>: Configure
Use Case: Wireless Networking for Digital Signage
1. Scenario A media company operates a network of digital advertising screens located at bus stops and outdoor plazas. Challenges: Laying wired internet cables to these scattered outdoor locations is expensive. Technicians currently have to visit each
Use Case: Remote Monitoring and Control of Water Pump Stations
1. Scenario Background A water management company manages multiple sewage lifting stations and clean water pump stations located in remote, scattered areas. These sites operate in harsh environments and are often unmanned. The company faces the following
MobiusPi API
MobiusPi API Manual (internal development interface) https://sdk.ig.inhandnetworks.com/en/latest/API-manual-EN.html The internal working principle of the gateway is to provide Python developers with a function library that directly accesses the underlying
IR315 Electronic Police
1. Scene background At the intersection of a residential area in the city center, two sets of electronic police officers were installed to capture red light running and illegal lane changes. they have encountered three troubles before: firstly, the high-definition
IR302 helps office building elevators achieve 'Quick fault alarm'
1. Scene background Previously, elevator problems relied on two methods: either passengers were trapped and pressed for emergency calls, or the property management manually climbed the stairs for weekly inspections. For example, when the elevator suddenly
IR302 how to reset
IR302 how to reset
What built-in tools are available for network diagnosis?
The router includes three main tools under the "Tools" menu: PING Probe: To check connectivity to a destination host. Route Probe (Traceroute): To detect routing faults and hop counts. Network Speed Test: To test upload/download speeds (results are viewed
How can I allow external networks to access a specific service on my internal LAN?
You can use the Port Mapping feature (found under "Firewall >> Port Mapping"). This forwards data sent to a specific port on the router's WAN IP to a specific internal IP and port on the LAN. The router supports up to 50 port mapping rules.
What is VRRP and how is it used?
VRRP (Virtual Router Redundancy Protocol) groups multiple routers to form a single virtual router to act as a gateway. If the master router fails, a backup router takes over the gateway duties based on priority, ensuring uninterrupted communication for
How do I upgrade the system firmware?
Firmware upgrades are done via the "System >> System Upgrade" menu. The process involves: Clicking <Browse> to select the upgrade file. Clicking <Upgrade> and confirming. Once successful, restart the device for the changes to take effect . Note: Do not
What is IP Passthrough?
IP Passthrough allows the router to distribute the IP address obtained by the WAN port directly to a device connected to the LAN port. This is often used when an external device needs to be directly accessible from the outside. Only one device can obtain
How does the Traffic Management feature work?
This feature provides traffic statistics for the dial-up interface. You can set a monthly traffic threshold. If the traffic exceeds the set threshold, the device can perform actions such as sending an alarm, blocking all non-management traffic, or closing
How do the Digital Input (DI) and Digital Output (DO) interfaces work?
DI (Digital Input): Supports an input voltage of 0-30V. 0-3V is considered "low," and 10-30V is "high." The maximum input current is 100mA. DO (Digital Output): It is a wet contact output with resistor pull-up. Low level is 0V, and high level is 12V.
Can I manage the router using SMS commands?
Yes, the router supports SMS management, which allows you to restart the device or manually connect/disconnect the network via text message. You must enable the function and configure the allowed mobile numbers. You can also set a "Status Query" command
What are the different WLAN (Wi-Fi) working modes supported?
The IR302 WLAN interface supports two types: Access Point (AP) and Client (STA). AP Mode: The device acts as a wireless access point for other devices to connect to, supporting various authentication methods like WPA/WPA2. STA Mode (Client): The device
What do the different colors on the Signal LED indicate?
The Signal LED indicates the cellular signal strength: Red: Weak signal (Signal value 0~10). Yellow: Medium signal (Signal value 11~20). Green: Strong signal (Signal value 21~30). Off: The signal function is not enabled.
Does the router support serial data transmission (DTU)?
Yes, specific models (IR302-<WMNN>-<WLAN/Null>-S) support DTU functionality. This allows the device to forward data from the serial port (RS232 or RS485) to a user-configured server. It supports transparent transmission via TCP or UDP protocols.
What is the Link Backup feature?
Link Backup ensures continuous communication by switching to a backup link if the main link fails. Main Link: Can be set to WAN port or Dial-up interface. Backup Modes: Hot Backup: Both links are online; switches immediately if the current one disconnects.
Does the IR302 support remote management?
Yes, the IR302 supports the InHand Device Manager "Device Cloud" management platform, which allows users to manage devices remotely. You can configure this in the "Services >> Device Remote Management Platform" menu. Supported modes include "Device Manager"
What should I check if the router cannot access the Internet after powering on?
If the device cannot connect to the internet, please check the following: Ensure the SIM card is inserted correctly. Verify the SIM card has data service enabled and is not in arrears. Check if dial-up parameters such as APN, dial-up number, account,
How do I install the SIM card?
The IR302 uses a pop-up card slot. To install the SIM card: Insert the SIM card pin into the round hole on the left side of the card slot and press to pop the holder out. Place the SIM card into the holder. Press the holder back into the card slot.
Which VPN protocols does the IR302 support?
The IR302 supports a wide range of VPN protocols to ensure secure data transmission, including: IPSec GRE L2TP Client PPTP Client OpenVPN WireGuard ZeroTier
What are the power supply requirements for the IR302?
The device supports a DC power input range of 9~36VDC. It can also be used with a 220V AC power adapter provided with the product. When installing, ensure the ripple is less than 100mV.
Next Page