• IR302 Continuously Disconnecting and Reconnecting

    Hello, I recently purchased an Inhand IR302 to provide a cellular connection to a computer via ethernet. I have a SIM card that I put in the IR302. When I configure it for AT&T it says “detecting modem” and after a few seconds it connects. However, after

  • modem EC20 is not supported! bad driver?

    I have a IR302. when the cellular si enapbel i have this log : starting modem... info Feb 21 02:12:02 redial[1258] modem is started. info Feb 21 02:12:13 redial[1258] scanning modem (13/30)... info Feb 21 02:12:13 redial[1258] scanning wan1 => /dev/ttyS1

  • IR302 Unauthorized Devices Blocking

    Problem Scenario Client has a IR302 router, and an authorized card reader and a controller are connected to the router, for regular operation. But recently there are two more unknown devices connected to the router, and they consume some internet data.

  • Status report activation

    I'd tried to enabling status report on ir302, but on the modem log like this : 31> Aug 7 06:12:31 rmonthird[4304]: HTTP:Hostname:xxx.id, Port:80, Post_filename: <31> Aug 7 06:12:31 rmonthird[4304]: TCP or HTTP:server=[x.x.x.x], server_port=[80] <31> Aug

  • Status Report Activation

    I'd tried to enabling status report on ir302, but on the modem log like this : 31> Aug 7 06:12:31 rmonthird[4304]: HTTP:Hostname:xxx, Port:80, Post_filename: <31> Aug 7 06:12:31 rmonthird[4304]: TCP or HTTP:server=[104.21.25.150], server_port=[80] <31>

  • Device Manager - Gateway - "Online Duration" Value (how is this determined)

    Within the Device Manager cloud platform, when I go to Gateways and select one of my IR302's, under the summary at the top of the page, it shows "Online Duration". How is this "Online Duration" value calculated? I ask because this could refer to the device's

  • How to set up IP Passthrough

    Background: IP Passthrough allows the router to act as a bridge, passing the IP address it receives from the carrier to one attached device. Once the router is in IP Passthrough mode, using the IP will only reach the end device and remote access to the

  • IR302 send SMS

    Hi, I have several IR302 modem installed in remote locations. I need to retrive the sim phone number used on those modem. is there a way to have them send an sms?

  • openvpn client ir302

    I created an openvpn client connection that connects to the privatevpn server, but as soon as I connect the vpn the internet stops working. instead I need to browse with the public IP that privateVPN assigns me. what is missing in the configuration?​

  • IR302-FQ38-WLAN band locking

    Hello All, I use an IR302-FQ38-WLAN router with Verizon in the U.S. The router uses any of bands 2, 4, or 66 in my location. Is there a way that I may specify which bands the router will use? Any way to do band locking. It is OK with me if command line

  • IR300/CR202 Link Backup

    If you want to use your regular internet as your primary, and use cellular as backup when your primary is down, IR302/305 or CR202 Link backup function could help you switch the uplink automatically. Note: Only CR202 with firmware V1.0.13 or later support

  • WLAN WDS mode

    the manual seems to indicate that the WiFi can be used to connect to a WLAN or it can be used to provide an access point over which other devices can connect. Is it possible to do both at once? We would like to have the option for the end-customer to

  • IR302 setup VPN for one internal IP and bypass VPN for Wifi user

    Hello, I have setup an IR302 Router with a VPN service. I am able to use the VPN IP address for the system and connect to a modbus device that is plugged into the LAN port. However the VPN is not as fast as my ISP. I have been trying to figure out the

  • How to set up link backup

    1. Connect the PC to the router directly via Ethernet. Go to 192.168.2.1 on a web browser and login with default credentials (adm/123456). 2. Go to Statusànetwork connections, confirm the Internet connection status in WAN mode, cellular mode and Wi-Fi

  • Verizon SIM Card's Static and Dynamic IP Setting

    1. Get a dynamic IP You don’t need set anything, just keep the default settings, inhand router could automatically register VzW network and get a dynamic IP. 2. Get a Static IP You got a Verizon SIM card and it could get a static IP, then in the inhand

  • How to configure DDNS in IR302?

    1. Open Web site http://www.noip.com create an account Put in Email Username Password Domain name. P-1 2. Confirm the email sent by NoIP and verify the account by clicking "Confirm Account". P-2 3. Log in NoIP P-3-1 P-3-2 4. ConfigIR302 4.1 Make sure

  • How can I access my IR302 when I enable IP Passthrough？

    The LAN ip of IR302 will change after you configure IP Passthrough. It becomes the first 16 bit mask IP in the IP segment assigned by the operator to the downstream device of IR302. You can also check the gateway of the downstream device, and that IP

  • How to configure Link Backup between Wired and Wi-Fi for IR302?

    1. Go to Network >> WAN.We select Static IP for the WAN connection, and configure the WAN portas follows: 2. Configure WLAN as STA mode. 1) Go to Network >> WAN(STA), selectDHCP for WLAN connection. 2) Go to Network >> WLAN(Client), and then click Scan.Now

  • How to configure Link Backup between Wired and Wi-Fi for IR302?

    1. Go to Network >> WAN.We select Static IP for the WAN connection, and configure the WAN portas follows: 2. Configure WLAN as STA mode. 1) Go to Network >> WAN(STA), selectDHCP for WLAN connection. 2) Go to Network >> WLAN(Client), and then click Scan.Now

  • What is the Dual-SIM switch mechanism of IR302?

    Main SIM card is the SIM card that enables dialing first after the device is on. When Main SIM is disconnected for some reason or fail to dial up, and then Backup SIM will be on. The settings of Max Number of Dial, CSQ Threshold and Min connected time

  • How to configure WLAN STA mode in IR302?

    1) Go to Network ->Switch WLAN Mode, select STA. 2) Reboot after apply the configuration. 3) Go to Network >> WAN(STA), selectDHCP for WLAN connection. 4) Go to Network->WLAN Client, apply the default configuration first. 5) Click Scan, and then connect

  • How to configure the IR302 as WLAN WDS?

    1) Select AP mode. Go to Network-> Switch WLAN Mode. The default mode of WLAN is AP. After the switch of mode, it needs a reboot to take effect. 2) Go to NETWORK->WLAN. Enable WLAN functionality. You’ll see the Wi-FI LED is flashing. 3) Enable WDS. Configure

  • How to configure WLAN AP mode in IR302?

    1) Select AP mode. Go to Network-> Switch WLAN Mode. The default mode of WLAN is AP. After the switch of mode, it needs a reboot to take effect. 2) Go to NETWORK->WLAN. Enable WLAN functionality. 3) Change (if you wish) the SSID and the password. 4) Verify

  • IR302 Link Backup

    If you want to use your regular internet as your primary, and use cellular as backup when your primary is down, IR302 Link backup function could help you switch the uplink automatically. By default, WAN/LAN port on IR302 is a LAN port, we need to change

  • Connect the downstream devices of two different sites through InConnect

    I would like to connect IR302 routers in a way where all downstream devices can see each other. How would I go about doing this through InConnect? 1.Create the InHand Routers on InConnect dashboard, and then add the downstream devices. You can refer to

  • What is the power required to get it to work, can we connect it to a dc solar panel and batteries?

    What is the power required to get it to work, can we connect it to a dc solar panel and batteries?

  • How to do Hardware Restore?

    I have a router. The model is IR902. I can not remember the password. How to restore it?