Use Case: Secure Networking for Smart ATMs & Financial Kiosks
1. Scenario A commercial bank plans to deploy a fleet of new "Smart ATMs" and self-service financial kiosks in shopping malls and convenience stores. Challenges: Security: Financial transaction data requires the highest level of encryption and protection
Use Case: Wireless Networking for Digital Signage
1. Scenario A media company operates a network of digital advertising screens located at bus stops and outdoor plazas. Challenges: Laying wired internet cables to these scattered outdoor locations is expensive. Technicians currently have to visit each
Use Case: Remote Monitoring and Control of Water Pump Stations
1. Scenario Background A water management company manages multiple sewage lifting stations and clean water pump stations located in remote, scattered areas. These sites operate in harsh environments and are often unmanned. The company faces the following
IR315 Electronic Police
1. Scene background At the intersection of a residential area in the city center, two sets of electronic police officers were installed to capture red light running and illegal lane changes. they have encountered three troubles before: firstly, the high-definition
IR302 helps office building elevators achieve 'Quick fault alarm'
1. Scene background Previously, elevator problems relied on two methods: either passengers were trapped and pressed for emergency calls, or the property management manually climbed the stairs for weekly inspections. For example, when the elevator suddenly
IR302 Blocking Unknown Devices (WIRED)
Problem Scenario Client has a IR302 router, and an authorized card reader and a controller are connected to the router, for regular operation. But recently there are two more unknown devices connected to the router via RJ45 (wired), and they consume some
IR300 connect/disconnect are not working with mqtt integration
Hi, From https://iot.inhandnetworks.com/ under integrations, I created mqtt event type with event type connect, disconnect, device.info, series, lbs to test a device which is under Gateways (selected a single device) and I tried to test rebooting the
IR302 Unauthorized Devices Blocking
Problem Scenario Client has a IR302 router, and an authorized card reader and a controller are connected to the router, for regular operation. But recently there are two more unknown devices connected to the router, and they consume some internet data.
İnhand ir 915l reboot problem
Hello, my ir 915L router has a constant rebooting problem, it keeps restarting after doing a startup reset and it has not improved in any way. I could not connect in any way, including WiFi and ethernet.
Status report activation
I'd tried to enabling status report on ir302, but on the modem log like this : 31> Aug 7 06:12:31 rmonthird[4304]: HTTP:Hostname:xxx.id, Port:80, Post_filename: <31> Aug 7 06:12:31 rmonthird[4304]: TCP or HTTP:server=[x.x.x.x], server_port=[80] <31> Aug
Status Report Activation
I'd tried to enabling status report on ir302, but on the modem log like this : 31> Aug 7 06:12:31 rmonthird[4304]: HTTP:Hostname:xxx, Port:80, Post_filename: <31> Aug 7 06:12:31 rmonthird[4304]: TCP or HTTP:server=[104.21.25.150], server_port=[80] <31>
Setting up Router to prevent attacks with Public Static IP SIMs
1. Background Having a public static IP enables users to access their device from any location on the Internet, granting them extensive control over the device's functionalities as long as it remains online. However, this convenience comes with a security
How to set up IP Passthrough
Background: IP Passthrough allows the router to act as a bridge, passing the IP address it receives from the carrier to one attached device. Once the router is in IP Passthrough mode, using the IP will only reach the end device and remote access to the
inhand IR624 5G SA connecting issue
Hi, we are currently testing the equipment in connecting our Private 5G network. Configuration from the "Internet" page has been done, as in the attached picture. We do not have authentication method, but there is no "None" selection in the combo box.
inhand IR624 will not do a hard reset
Hello all, I seem to have a problem with one of our modems, the modem was previously used by a colleague who set a different modem login password, but forget this. Because I want to change the IP range in need to do a hard reset. The modem works fine,
IR302 firmware
Hi, i recently bought 9 routers IR302 and 3 of its has a lower firmware v3.5.50, the others has v3.5.59. Where can i found the newer firmware (in the download section only are available the v3.5.50), the problem that i have is when i try to import the
inhand 302 Wireguard route
Hi, I have an issue where the inhand drops the route to my allowed IP subnet from its routing table after a certain period of time. Re-initiating the tunnel resolves this. Is there an solution to this? unfortunately the wireguard interface does not show
How to port forwarding with config default gateway on InHand IR302
I have a old PLC. I can config the PLC's LAN IP(192.168.2.2) address manually but there is no Default Gateway setting. And I have IR302 with a public statip IP(166.123.4.9) address from SIM provider. Since I can not config default gateway on PLC, I want
IR-302 WireGuard
WireGuard not connecting and not showing any data in the logs. - Configuration is confirmed as correct.
Device Manager showing Gateway as "not SYNC"
Hi, I am new to this forum, sorry if I am not asking this question in the right place. I have some IR300 routers deployed and working. But one of them lost access due to some unknown reason. Maybe the low battery level during some time put it in a bad
SNMP MIB files on InHand IR615s
Where can I download the mib files that are specific to this model IR615s ? Is seems that INHAND-MIB and INHAND-3GWAN-MIB files whould give us the LTE SIGNAL LEVEL via SNMP. Thank you.
WAN cannot get IP Address
I have issue on my inhand IR615. I have setting IPSec for my project and i need connected to configurable ip address WAN but it stuck (see the picture). I already follow many suggestion from manual book, community (inhand website), youtube tutorials but
port mapping/forwarding of IR615
I've got a Verizon static SIM card, and I added APN manually to make it work. Now I want to use this static IP to access my controller connected to the IR615.
Modem replacement for IR615 HW 30108
Can someone advice on a list of compatible modem for IR615 HW 30108, EU region, capable of 2G and 4G? If someone has a 4G model of this router, EU model, the first eight letter of IMEI indicate the hardware model of modem.
How to set up port forwarding
Background: Port forwarding is used to allow the router to forward traffic from a public IP to another interface (typically LAN). This allows a user to reach a device on the router through the public web. In addition, if multiple devices use the same
Application Guide for Easy OpenVPN Multiclient Mode Setup
1. Summary A VPN tunnel is an encrypted connection between your device and a VPN server. OpenVPN is currently considered the top form of VPN tunneling protocol. That's because its encryption is especially strong. It's also adept at getting past firewalls.
IR300/CR202 Link Backup
If you want to use your regular internet as your primary, and use cellular as backup when your primary is down, IR302/305 or CR202 Link backup function could help you switch the uplink automatically. Note: Only CR202 with firmware V1.0.13 or later support
Connecting with Siemens Sm@rtClient using InHand router IR615
Good morning, I have an InHan IR615-WLAN router (firmware version 2.3.0.r4870) connected to an automations with PLC, Panel Pc, vison systems, robots ect. It was configured by importing a backup from another modem currently running. The router is connected
Upgrade the firmware of IR915 to a fixed version
Notice: Upgrade the latest firmware if your IR900 product current firmware version equals or is lower than r8968, otherwise which maybe causes unexpect restart or another unstable symptom. Preparation： Save running configuration and export it. Go to Administration
Override WAN DNS provided by wireless carrier on IR611
Hello, We're looking to test out some routing changes and we need the ability to replace the WAN-provided DNS primary/secondary IPs with our own. I've tried using the router's portal (it's an IR611) but that doesn't seem to do the trick. Is there a way
How to setup Wi-Fi on IR900
1. Connect PC directly to router via Ethernet and log into router at 192.168.2.1 using default credentials (adm/123456) 2. Go to NetworkàWi-Fi, and check the Enable. 3. Change the Station Role to AP. Change SSID if needed. Change Auth Method to WPA2-PSK.
Issues with remote connecting to private network
hi there i just received my IR300. Hoping to set it up with OpenVPN to access some remote farm devices. My network looks like the below (obviously, IP addresses here are not real values): - Router 1: ADSL Intenet Router (IP:192.168.100.0/24) - Router
can not get IR302 to function properly??
WAN TO CELL FAIL OVER.. CELL TO LAN / WLAN as i have had it this way for some time now..my question is if i want it to work in reverse. Main Link =Cellular 1, and Backup Link=WAN, it does not work now, i have all 9 of my devices IR302's at current firmware.
telnet to computer connected to cellular router
I have an IR302 I am using one sim card from tello mobile and one from flexiboom. I would like to telnet to a raspberry pi connected to the router. Is there a way to do this through cellular connection.
Band Steering
Is there any way to do band steering on the 302, so I can pick what channel I want to use?
Slow 4G connection - Telstra Australia
The SIM I inserted into my IR302 would get speeds of 60-80mbps in a different modem and upload 20-40mbps. Through my inhand device it is 5 up and down gove or take. Are there setting I can change? How do I get better speeds?
Traffic Stats Log
I would like to be able to see what websites are being accessed from our IR302 routers, but I am unable to setup any of the status reports and nothing in the device manager shows me any useful data either. Anyone have success with this? Just wanting more
VLANs cannot access Internet.
We have a IR615 router with 4G service, and we have setup the default VLAN (VLAN ID=1, port LAN 1) with IP 10.30.0.1/24. Everything else is default settings. When I plug in a laptop with IP address 10.30.0.101, GW=10.30.0.1, DNS=8.8.8.8, I am able to
InRouter305 Site-to-Site Connectivity
Looking for assistance in configuring a site-to-site cellular connection using the InRouter305. Is there a best practice for setting up this connection with this particular product? Do I need to use InConnect to successfully setup this connection? Any
Help configuration VPN router IR915L vs Meraki Firewal
It is a pleasure to greet you and request your support to know if any of you have carried out VPN tests between an IR Router and a Meraki device or better yet, how to configure the IR so that all the data is sent to a private IP address in a linear way.
Next Page